Seam repair
Failed seams get a new cover strip so they stay closed.
Flat Roofing
Rubber Roof Repair Lyndhurst, NJ
A roofer in Lyndhurst can repair a rubber roof by cleaning and priming the EPDM, then sealing open seams, punctures and torn flashing with rubber cover tape and lap sealant, once the actual leak point is located. Call (551) 348-2859 to reach a local roofer.
A rubber roof is tough, but its weak points are well known. The seams fail first on many older rubber roofs, because the original seam adhesive loses its grip after years of sun. After that, punctures and torn flashing at walls and penetrations cause most leaks.
EPDM also shrinks as it ages. Shrinking rubber pulls tight at the perimeter, tenting across corners and tearing at flashing seams. The fix is releasing the tension and adding new flashing, not just caulking the gap.
One mistake makes rubber roof repair much harder. Petroleum-based patches attack the rubber and have to be scraped off before a real repair. For now, protect the inside, avoid the roof in wet weather and write down when the leak shows up.
If the problem goes deeper than it first looked, a Lyndhurst roofer may also recommend rubber roof installation or flat roof repair.
Looking for Lyndhurst rubber roof repair? Call (551) 348-2859 and describe the problem to a roofer who works in Lyndhurst.
Call nowThe process
What happens during a rubber roof repair
A rubber patch is only as good as the cleaning and priming under it.
Inspect the roof
The roofer checks every seam, flashing detail, pipe boot and the roof edge, probing laps for loose spots. If insulation is wet, it is cut out and replaced before patching.
Clean the rubber
Weathered EPDM is scrubbed with a membrane cleaner to remove dirt, chalking and oxidation. Earlier tar repairs are cut away.
Apply primer
EPDM primer is scrubbed into the surface and allowed to flash off until it is tacky but not wet. Skipping primer is the most common reason patches peel.
Patching
Peel-and-stick EPDM cover tape or a cured patch is cut with rounded corners, pressed down and rolled firmly with a seam roller. Corners and penetrations use flexible uncured flashing.
Seam repair
Peeling seams are stripped clean and sealed again with primer and tape. Lap sealant is applied along exposed edges and T-joints.
Wall flashing
Bridged corners are cut free and new flashing is installed to relieve stress. New termination bar and counter flashing keep the top edge sealed.
What is included
Repairs a rubber roofer can handle
Coating
Compatible coatings can extend the life of weathered EPDM after proper priming.
Pipe boots
Cracked pipe boots and vent flashing are replaced with pre-molded boots or uncured flashing.
Shrinkage repair
Shrunk edges get new flashing with termination bar where needed.
Tear repair
Punctures get a primed rubber patch with rounded corners.
Related service
EPDM Roof Repair Lyndhurst, NJ
EPDM roof repair follows a strict sequence: clean, prime, patch, roll and seal. A clean, dry surface, a properly dried primer and a firmly rolled patch are what make an EPDM repair hold. A bead of lap sealant seals the patch edges.
In Lyndhurst, rubber roof repairs are best done on dry days when the membrane is not too cold. In an emergency, a temporary seal can stop water until conditions allow a proper patch. A proper patch should follow as soon as possible.
Related service
Rubber Roof Replacement Lyndhurst, NJ
Sometimes a rubber roof is too far gone to repair. Seams failing all over, shrinkage pulling at every wall, a brittle and crazed surface or wet insulation across large areas all point toward a new roof. Testing the insulation helps make the call.
Replacement options include new EPDM or a heat-welded membrane like TPO. A tear-off is needed if the insulation is wet or there are already two layers. Ask the Lyndhurst roofer to compare repair and replacement for your roof.
Local help
Rubber Roof Repair Near Me
Around Lyndhurst, rubber roofing is found on additions, carports and flat roofs that have been in place for years. Homes in Lyndhurst and nearby places including Rutherford, North Arlington, East Rutherford and Wallington get the most from an EPDM roof when seams and flashing are checked every year or two, and early repairs keep the insulation dry.
For rubber roof repair in Lyndhurst, NJ or nearby towns like Rutherford, North Arlington, East Rutherford and Wallington, call (551) 348-2859 to reach a roofer who covers your street.
How the weather here affects roofs around Lyndhurst
Cold winters bring snow, ice and a long stretch of freezing nights. When warm attic air melts the snow, the meltwater runs down and freezes again at the eaves, which is how ice dams form and back water up under the shingles. Coastal storms and heavy spring rain drive water sideways into flashing, valleys and old chimneys. That is why roof repair in Lyndhurst is busiest after a hard winter and before the next one.
Why call
Why not wait
Less damage
Small roof problems caught early usually stay small repairs.
Roofers who know Lyndhurst
Local roofers see the same roofs and storm damage across Lyndhurst and nearby towns.
Clear next steps
Ask the roofer about the cause, the options and the estimate before work starts.
Rubber Roof Repair FAQ
Why is my rubber roof pulling away from the wall?
Aging rubber contracts over time. Tension builds at walls and edges, and the flashing eventually tears. Repairs release the strain and reflash the wall.
Can I use roofing tar on a rubber roof?
Asphalt-based products damage rubber roofing. Their solvents soften and swell the rubber, and they leave a surface that proper EPDM patches cannot bond to. Use primer, EPDM cover tape and lap sealant instead.
What is the right way to patch EPDM?
The surface is cleaned, primed and covered with rubber patch material. The roofer scrubs the area with membrane cleaner, applies primer, lets it flash off, then presses down a patch with rounded corners and rolls it firmly. Lap sealant finishes the edges.
What is the lifespan of an EPDM roof?
A well installed EPDM roof commonly lasts 20 to 30 years. Thickness, installation and maintenance all affect its life. Fixing small problems early protects the rest.
Can a rubber roof be coated?
A coating can extend the life of aging EPDM. Repairs and a compatible primer come first, then the coating. Coatings do not fix wet insulation.
More questions? Call (551) 348-2859
Often needed together
Rubber Roof Installation
EPDM rubber roof installation with the right thickness, attachment method and flashing details, so the roof stays flexible and watertight for decades.
Learn moreFlat Roof Repair
Repairs for leaking flat roofs, from punctures and seams to clogged drains and wet insulation, with the patch made from material that bonds to what is there.
Learn moreRoof Coating
Liquid-applied roof coatings that seal seams, reflect heat and add years to a roof, after the seams and blisters are repaired.
Learn moreRoof Leak Repair
Stopping water at the pipe boots, flashing, valleys and nail holes where roofs actually leak, before wet decking and insulation turn into rot.
Learn more
Looking for something else?
See all roofing servicesGet rubber roof repair help in Lyndhurst
Call (551) 348-2859 to talk to a roofer serving Lyndhurst, NJ.