Roof covering
Starter strip, field shingles and ridge caps, or the panels and trim for a metal roof with fasteners placed where they belong.
Installing a roof in Lyndhurst comes down to doing each layer in order, from the metal edges and underlayment to the flashing and the final ridge, and most of what makes a roof last happens before the first shingle goes down. Call (551) 348-2859 to reach a local roofer.
Most early roof leaks are installation problems, not material problems. High nailing lets wind peel shingles off, a skipped kickout flashing sends water down into the wall and a poorly cut valley lets water work sideways under the shingles. By the time they show up, the stain is already on the ceiling.
Before anything is ordered, the roofer and homeowner settle on the roofing material. Architectural, or dimensional, asphalt shingles are the most common choice on houses, with thinner three-tab shingles still used on some homes and sheds, while standing seam or exposed fastener metal, concrete or clay tile and slate each need their own methods and fasteners. Roof pitch matters too, since standard shingles need enough slope to shed water and very low pitches call for a membrane instead.
It helps to bring a few details to the first conversation. Mention whether the old roof is coming off or this is new framing, what material you have in mind and any spots that have leaked before.
Many roof installation calls in Lyndhurst also turn up a need for roof replacement or shingle roof installation.
Looking for Lyndhurst roof installation? Call (551) 348-2859 and describe the problem to a roofer who works in Lyndhurst.
Call nowEach layer protects the one under it, so the order is not optional.
Before installation, the crew walks the decking and replaces soft or damaged sections. On an overlay, the old shingles must lie flat, and any badly curled ones are cut back or replaced.
Drip edge goes on at the eaves, ice and water shield is rolled out along the eaves and in the valleys, and drip edge is then added along the rakes over the underlayment. This is the part of the roof most likely to see ice and backed-up water.
Synthetic underlayment or felt covers the rest of the deck, lapped so each row sheds over the one below. It is the backup layer if a shingle is ever lifted or broken.
Step flashing is woven in with each course along sidewalls, counter flashing covers it at masonry, kickout flashing sits at the bottom of each wall line and new pipe boots go over every vent. Flashing is where most leaks start, so it is never just caulked in place.
After a starter course, the crew lays shingles row by row, keeping the exposure even and the nails inside the nail strip. Valleys are finished as open metal, closed cut or woven, depending on the material and the plan.
Exhaust vents go in near the peak and the ridge is capped. Without enough soffit intake, a ridge vent cannot do its job.
Starter strip, field shingles and ridge caps, or the panels and trim for a metal roof with fasteners placed where they belong.
Drip edge at the eaves and rakes keeps water off the fascia boards.
Ridge vents or other exhaust paired with soffit intake which protects the roofing and the decking.
Step, counter and kickout flashing plus new pipe boots seals the places where the roof meets something else.
A full layer of underlayment plus ice barrier where water collects guards the deck if ice dams form.
A new roof installation can mean a roof on a stripped house, a roof on new framing or a roof on an addition tied into an existing one. Tie-ins between new and old roofs are a common leak point, so they need full ice barrier and careful flashing. It is worth asking how closely the new shingles will match the weathered ones.
Manufacturers publish exact steps for their products, and local code usually requires following them. When talking with a Lyndhurst roofer, ask about the nailing pattern, the underlayment and how intake and exhaust will balance. Vague answers about the hidden layers are worth noticing.
With an overlay, sometimes called a layover or recover, the new roofing goes on top of the existing shingles. It is only allowed on a roof with one existing layer that lies flat over a solid deck. It saves the labor of a tear-off and keeps the house closed during the job.
There are good reasons most roofers prefer a tear-off. Hidden rot stays hidden, flashing is often reused and the roof carries the weight of two layers. If an overlay is on the table, ask the roofer to confirm the layer count, replace the drip edge and flashing and explain what happens at the next replacement, when both layers must come off.
In Lyndhurst, new roofs go on everything from decades-old homes to recent builds. Older homes in Lyndhurst and nearby towns like Rutherford, North Arlington, East Rutherford and Wallington often need extra deck work and better ventilation, while newer homes are more likely to need flashing tied into new siding, so it is worth asking how each detail will be handled before the first bundle is opened.
For roof installation in Lyndhurst, NJ or nearby towns like Rutherford, North Arlington, East Rutherford and Wallington, call (551) 348-2859 to reach a roofer who covers your street.
Winters here are long and cold, with snow on the roof for weeks at a time and plenty of nights below freezing. When warm attic air melts the snow, the meltwater runs down and freezes again at the eaves, which is how ice dams form and back water up under the shingles. Coastal storms and heavy spring rain drive water sideways into flashing, valleys and old chimneys. Most homeowners in Lyndhurst, NJ have the roof checked in the fall and again after the snow melts.
Small roof problems caught early usually stay small repairs.
Local roofers see the same roofs and storm damage across Lyndhurst and nearby towns.
Ask your questions before you agree to anything.
More questions? Call (551) 348-2859
Replacing an aging roof with new underlayment, flashing, vents and roofing, built to current code from the decking out.
Learn moreNew shingle roofs built layer by layer on a sound deck, for new homes, additions and reroofs.
Learn moreMetal roof installation built around the right panel, finish and trim for the house, so the roof handles heat, wind and thermal movement.
Learn moreGetting new framing dried in fast and roofed to code, with flashing timed around windows and siding.
Learn moreLooking for something else?
See all roofing servicesCall (551) 348-2859 for a local roofer in Lyndhurst and nearby towns.