Framing repair
Soft framing at the roof edge is reinforced so the new board stays put.
Exterior Services
Fascia Repair Lyndhurst, NJ
A Lyndhurst roofer can repair the fascia boards that carry your gutters and cap the ends of the rafters, and check the rafter tails behind the board while it is off. Dial (551) 348-2859 to talk with a local roofer about the fascia.
Fascia rot nearly always comes from water getting behind the gutter. Clogged or poorly pitched gutters spill over the back, and a roof edge with no drip edge sends water straight down the fascia. The wood slowly loses strength until the gutter spikes or hanger screws no longer hold.
Rotted fascia is often the visible part of a bigger problem. Left alone, the rot moves into the rafter ends and the edge of the roof deck, which turns a trim repair into structural work. On homes with metal fascia wrap, the rot often goes unseen until the gutter falls.
Before the visit, take a look along the roof edge from the ground. Write down which sides of the house show peeling paint, gaps or a sagging gutter. Mention whether the fascia is painted wood, PVC or covered in aluminum, and how old the gutters are.
Depending on what the roofer finds, fascia repair in Lyndhurst, NJ can go hand in hand with soffit repair and gutter installation.
Need fascia repair in Lyndhurst? Call (551) 348-2859 and describe the problem to a roofer who works in Lyndhurst.
Call nowThe process
How fascia repair works
Here is how a roofer typically handles a fascia repair.
Check the edge
Before the board comes off, the roofer looks at what has been soaking it, from the shingle edge to the downspout. The length of the damage decides how much board is replaced.
Remove the gutter
The gutter section over the damage is unhooked and set aside so the fascia can come off. Old spikes and loose hangers are not reused.
Repair the framing
Soft rafter tails are cut back and sistered with new lumber, and rotted decking at the edge is replaced. This is the step that decides whether the repair lasts.
Fit the board
New fascia in primed wood, PVC or composite is cut to fit, with scarf joints at the seams. End grain is sealed so it does not soak up water.
Fix the edge flashing
Drip edge flashing is slid under the shingles and over the gutter back, so water cannot reach the wood. It is a small part that does most of the work.
Reattach gutters
The gutter is reattached with hangers spaced closely enough to carry water and debris. Wood fascia gets a finish coat of paint.
What is included
Fascia repairs a roofer can handle
Gutter reattachment
Sagging gutters are rehung on solid fascia with new hangers at the right slope.
Rotted board repair
Rotted sections of fascia are cut out and replaced with new boards with sealed joints and ends.
Edge flashing
New drip edge is tucked under the shingles over the gutter so water drops into the gutter.
Fascia wrapping
Metal wrap can be added over new or sound fascia to cut down on painting.
Related service
Fascia Board Replacement Lyndhurst, NJ
When rot runs along most of a wall, or the boards are split and warped end to end, replacing the full run of fascia is the cleaner fix. Replacing the whole run gives the roofer a clear look at every rafter tail and the edge of the roof deck. The choice of material affects upkeep, since wood needs paint while PVC and wrapped boards do not.
In Lyndhurst, fascia board replacement often lines up with a new roof or new gutters, since the roof edge is already being worked on. Make sure rotted boards are removed, not covered. Also ask about the size of the new boards, since fascia that is too narrow can leave gaps at the soffit and gutter.
Related service
Fascia Board Repair Lyndhurst, NJ
Localized fascia damage, often at corners and below gutter joints, can usually be repaired without replacing the whole board. The new piece is joined with an angled scarf joint so the seam is strong and less likely to open. For a shallow soft spot, an epoxy consolidant and filler can restore the surface without cutting the board.
Patching a fascia board in Lyndhurst without fixing the gutter or drip edge above it just buys a season or two. The cause is often a leaking gutter corner or a downspout that backs up. Done right, the repair is hard to spot once painted.
Local help
Fascia Repair Near Me
Around Lyndhurst, fascia rot usually shows up behind gutters that overflow or along roof edges built without drip edge. Across Lyndhurst and nearby communities including Rutherford, North Arlington, East Rutherford and Wallington, the fascia under trees and heavy gutter loads is the first to go, which is why keeping gutters clear does so much to protect the fascia.
Searching for fascia repair near me from Lyndhurst or Rutherford, North Arlington, East Rutherford and Wallington? Call (551) 348-2859 to talk to a roofer who works in your part of town.
How the weather here affects roofs around Lyndhurst
Winters here are long and cold, with snow on the roof for weeks at a time and plenty of nights below freezing. Heat escaping from the attic melts snow on the upper roof, and the water refreezes at the colder eaves, which is how ice dams form and back water up under the shingles. Strong coastal storms push rain into every weak spot at the flashing and valleys. Most homeowners in Lyndhurst, NJ have the roof checked in the fall and again after the snow melts.
Why call
Why not wait
Drier ceilings
Small roof problems caught early usually stay small repairs.
Familiar with local homes
Local roofers see the same roofs and storm damage across Lyndhurst and nearby towns.
Straight answers
Ask your questions before you agree to anything.
Fascia Repair questions
Is it safe to wrap rotted fascia in aluminum?
Covering rotted wood with aluminum hides the rot instead of stopping it. The gutter hangers still screw into the wood behind the wrap, so they loosen as the board softens. Wrap is a good finish over new or solid fascia.
Do fascia boards affect my gutters?
Gutters hang from the fascia, so their strength depends on it. Soft fascia lets the fasteners work loose, which is often the first sign of rot. Repairing the fascia and rehanging the gutter with hidden hangers fixes both problems at once.
Do I need new fascia boards or just a repair?
Short sections of rot can be repaired by cutting out the bad wood and scarfing in a new piece. When rot runs along most of a wall or the boards are split throughout, full replacement makes more sense. Either way, the rafter tails behind the board need to be checked.
What is the best material for fascia?
PVC and composite fascia resist rot and hold paint well. Primed wood is easy to match on older homes but needs regular paint. No material holds up if water keeps running behind the gutter.
What causes fascia boards to rot?
Water getting behind the gutter is the main cause. Overflowing gutters, gutters pitched the wrong way and roof edges without drip edge soak the board repeatedly. Bare end grain and failed paint let water soak in faster.
More questions? Call (551) 348-2859
Other services that may help
Soffit Repair
Repairs for rotted, sagging or loose soffit panels under the roof eaves, so the attic breathes and the overhang stays sealed.
Learn moreGutter Installation
Seamless gutter installation sized to the roof, pitched to the downspouts and hung on hidden hangers, so water ends up where it should.
Learn moreGutter Repair
Gutter repair for leaking seams, sagging runs, loose hangers and broken downspouts, without replacing gutters that still have life in them.
Learn moreRoof Repair
Fixing the shingles, flashing, boots and decking that let a roof down, so a sound roof keeps working for years.
Learn more
Looking for something else?
See all roofing servicesGet fascia repair help in Lyndhurst
Call (551) 348-2859 for a local roofer in Lyndhurst and nearby towns.